BOSS Audio Systems BASS8K 8 Inch Powered Car Subwoofer and Amplifier Wiring Kit Package – 800 Watts Max Power, Under Seat, Low Profile, 8 Gauge Wiring Kit, for Truck Boxes and Enclosures

Product description

Break Your Subwoofer In

Much like the engine of a new automobile, a new subwoofer must go through a short but important process of “break-in” before it is run under harsh conditions. The “break-in” process will ensure the subwoofer is able to perform as it has been designed to.

This process involves subjecting the subwoofer to no more than low-to-medium volume levels for a number of hours in the enclosure. 3-4 hours is generally sufficient for the subwoofer’s suspension to loosen enough to prevent the voice coil(s) from overheating and causing failure.

The break-in period is also effective in extending subwoofer life. Over-driving the woofer before it has been properly broken-in will usually result in premature failure and poor performance.

Class A/B Topology, 800 Watts Peak Power, Low Profile 8″, Butyl Rubber Surround, Aluminum Cone PWM MOSFET Power Supply, RCA & Speaker Level Inputs, Low Pass Filter Bass Boost, Phase Control, Remote Subwoofer Control, LED Status Indicator Thermal, Short and Overload Protection Circuits KIT INCLUDES – 17 ft. 8 Gauge Red Power Cable, Competition High-Quality 40 Amp Fuse Holder 3 ft. 8 Gauge Black Ground Cable, 16 ft. 18 Gauge Blue Remote Cable, 16 ft. RCA Interconnect (7) 4″ Wire Ties, (1) Plastic Grommet, (1) #10 Gold-Plated Ring Terminal (1) Butt Splice Wire Connector, (1) Tap Screw, (1) Large Black Rubber Terminal Boot

High and Low Level Inputs

High-level inputs accept speaker output signals and low-level inputs accept pre-amp output signals to allow for the addition of amps and processors to standard factory or aftermarket source units.

MOSFET Power Supply

Metal Oxide Semiconductor Field-Effect Transistors quickly switch from full to non-conduction for high efficiency output.

Variable Low Pass Filter

Variable low-pass filter gives you control over the frequencies that pass through to the subwoofer.

Variable Bass Boost

Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.

Phase Control

Phase control lets you switch the speaker phase with the amp if your speakers or subwoofer are hooked up “out of phase”.

Low Profile

Low-profile subwoofers are a great choice for space-constrained areas without compromising on power and performance.

Short Protection

Automatic shut-off protects the amplifier if it gets too hot or if speakers fail causing a short.

Sub Control

A wired remote lets you easily control the subwoofer level for customized output and superior sou

KIT – 17′ red power cable w ring terminal & rubber boot pre-installed, 3′ black ground cable, 16′ blue remote cable, 40A fuse, 16′ RCA, 1 large black rubber terminal boot, 1 ring terminal, 7 wire ties, plastic groumet, 1 tap screw
Space Saver – If you are tight on space, this is a great solution for you. The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles. With a slim design, there are a few installation options
Pulse Width Modulated – PWM simplifies power supplies. It controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. Efficiency. Increased reliability
Variable Low-Pass Filter – A low-pass filter is an electronic circuit that removes all the notes below the filter’s frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
High Level Inputs – Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BASS8K to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs